Honeywell Thermostat honeywell programmable thermostat Uživatelský manuál

69-1631-1OWNER’S GUIDE® U.S. Registered TrademarkCopyright © 2003 Honeywell International Inc.All Rights Reserved CT3200 Programmable ThermostatWelcom

69-1631—1 10Six or more wiresIf your old thermostat has six or more wires (excluding clock wires attached to the C or C1 terminals), your heating/cool

11 69-1631—1Old thermostat terminals that do not match new thermostat terminalsUse the table below to wire the new thermostat.*Remove factory-installe

69-1631—1 12PROGRAMMINGFaceplate Illustration and DescriptionDescriptionsFig. 16. 1 Fan switch–Selects automatic fan operation or fan on.2 Set Schedu

13 69-1631—1Step 1. Set Current Time and DayStep 2. Learn About Programming FeaturesYour 3200 Thermostat allows you to program schedules for both a he

69-1631—1 14Programming Tips• You do not need to program times and temperatures for all program periods.If you decide not to program your thermostat,

15 69-1631—1Step 3. Program Heating Schedulea. Write in the times and temperatures that you want to program for your heating schedule.Heating Schedule

69-1631—1 16f. Press to display a blank schedule for the next program period (Fig. 22) and repeat steps d. through f. for each weekday program perio

17 69-1631—1Step 4. Program Cooling Schedulea. Write in the times and temperatures you want to program for your cooling schedule.b. Set the System swi

69-1631—1 18Verify that your cooling system worksIMPORTANT: To avoid damaging the compressor in the air conditioner, do not operate the cooling system

19 69-1631—1Set Fan and System SwitchesThe switches on the bottom of the thermostat faceplate control the operation of your fan and the heating and co

69-1631—1 2MERCURY NOTICEIf you are removing an old thermostat that contains mercury in a sealed tube (Fig. 1), do not place the old thermostat in the

69-1631—1 20d. Install new batteries. Make sure that positive and negative terminals are oriented as marked inside battery case.e. Close the battery d

21 69-1631—1Hold a temperature indefinitelyUse the Hold Temp feature when you want to maintain a constant temperature indefinitely, such as when you g

69-1631—1 22 FREQUENTLY ASKED QUESTIONSb. Press and simultaneously.A blank program schedule is displayed and the program is canceled (Fig. 31).Fig

23 69-1631—1CUSTOMER ASSISTANCEVisit us on the Web at www.honeywell.com/yourhome or call Honeywell Customer Care at 1-800-468-1502. Before you call, p

69-1631—1 J.S. Rev. 10-03 Printed in U.S.A. www.honeywell.com/yourhomeAutomation and Control SolutionsHoneywell International Inc. Honeywell Lim

3 69-1631—1 Step 1. Prepare for Installation1. Carefully unpack your new thermostat. Save your receipt and make sure you have the following parts:• Th

69-1631—1 4 Step 2. Remove Old ThermostatFig. 2. a. Turn off power to the heating/cooling system, either at the furnace or at the fuse/circuit breake

5 69-1631—1Step 3. Install Mounting PlateFig. 5. a. Separate the mounting plate from the thermostat using a coin, as shown in Fig 5.b. Position the m

69-1631—1 6Step 4. Set Thermostat for Your Type of Heating SystemIMPORTANT: IMPORTANT:Setting your thermostat correctly for your type of heating syste

7 69-1631—1Heating System TableStep 5. Wire Thermostat TerminalsType of SystemD I P S wit ch e s 1 and 2 Fuel SwitchWarm air, gas, or oil he

69-1631—1 8Step 6. Mount ThermostatFig. 11. Fig. 12. e. Align the tabs at the top of the thermostat with the tabs at the top of the mounting plate (

9 69-1631—1Step 7. Install the batteriesSpecial Wiring InstructionsClock thermostat with C or C1 terminalsA clock thermostat has one or two extra wire