Honeywell RTH7500D Uživatelský manuál

OWNER’S GUIDEPatents Pending® U.S. Registered Trademark© 2004 Honeywell International Inc. All Rights Reserved 69-1730RTH7500DProgrammable ThermostatT

69-1730 10Step 5. Label Old Thermostat Wires1. As you disconnect each wire, use the enclosed wire labels to wrap a wire label around each wire that ma

11 69-1730Step 6. Mount New Wallplate to Wall1. Separate the wallplate from the thermostat as shown.THERMOSTATWIRE HOLEM22267WALLPLATE69-1730.fm Page

69-1730 12Step 6. Mount New Wallplate to Wall (Cont)2. Pass the labeled wires through the wire hole on the wallplate.M22279WIRE HOLEWALL OPENINGWALLPL

13 69-1730Step 6. Mount New Wallplate to Wall (Cont)3. Position the wallplate on the wall with the arrow pointing up. Level the wallplate (for appeara

69-1730 14Step 6. Mount New Wallplate to Wall (Cont)4. Move the wallplate aside and drill holes at the locations marked on the wall. Drill 3/16 in. ho

15 69-1730Step 7. Connect Wires to New Wallplate1. Match the labeled wires to the letter designations on the wallplate.2. Select the correct letter de

69-1730 16Step 7. Connect Wires to New Wallplate (Cont)3. If wires are to be connected to both Rc and R, loosen the Rc and R screw terminals and remov

17 69-1730 Step 7. Connect Wires to New Wallplate (Cont)5. Loosen the screw terminals. Insert the labeled wires into the holes on the side of the term

69-1730 18Step 7. Connect Wires to New Wallplate (Cont)7. Compare letter designations on your old and new thermostats. Use the information below if yo

19 69-1730Step 7. Connect Wires to New Wallplate (Cont)1M22246If wires will be connected to both RC and R on the new thermostat,remove metal jumper wi

69-1730 2ContentsPrepare for Installation ... 3Follow Important Instructions ...

69-1730 20Step 7. Connect Wires to New Wallplate (Cont)8. Compare letter designations on your old and new thermostats. Use the information below if yo

21 69-1730Step 7. Connect Wires to New Wallplate (Cont)1M22245Leave metal jumper wire between RC and R in place.If the old thermostat had separate wir

69-1730 22Step 7. Connect Wires to New Wallplate (Cont)9. Push excess wire back into the wall opening. Keep wires in the shaded area.WALLPLATEM22297WA

23 69-1730Step 8. Install Batteries1. Install two fresh AA alkaline batteries on the back of the thermostat as marked on the thermostat.2. Remove tab

69-1730 24Step 9. Attach New Thermostat to Wallplate1. Align the screw blocks with the pins on the back of the thermostat.2. Push the thermostat strai

25 69-1730 Step 10. Set the CalendarThis thermostat is designed to automatically keep current time and day in memory for up to ten years, under normal

69-1730 26Step 10. Set the Calendar (Cont)8. Press the Done button.The calendar can be set anytime. See Step 11, Configure Installer Setup, for instru

27 69-1730Step 11. Configure Installer Setup1. Use the Installer Setup Menu to match your new thermostat to your heating and/or cooling system. Follow

69-1730 28Step 11. Configure Installer Setup (Cont)3. Press and hold the center button for approximately five seconds, until the screen changes.4. Rel

29 69-173011. Configure Installer Setup (Cont)5. Press the Up or Down arrows to select your setting for Installer Setup Number 0120 below.6. After you

3 69-1730Step 1. Prepare for Installation1. Check that the following items are included:If any of the items shown above are missing, call Honeywell Cu

69-1730 30Step 11. Configure Installer Setup (Cont)8. Press the Up or Down arrows to select your setting for Installer Setup Number 0170.9. After you

31 69-1730Step 11. Configure Installer Setup (Cont)10. If you do not have a number 0180 on the left side of your display, go to the next page.11. If y

69-1730 32Step 11. Configure Installer Setup (Cont)13. If you do not have a number 0190 on the left side of your display, go to the next page.14. If y

33 69-1730Step 11. Configure Installer Setup (Cont)16. If you do not have a number 0240 on the left side of your display, go to the next page.17. If y

69-1730 34Step 11. Configure Installer Setup (Cont)19. Press the Up or Down arrow to select your setting for Installer Setup Number 0320.20. After you

35 69-1730Step 11. Configure Installer Setup (Cont)21. Press the Up or Down arrow to select your setting for Installer Setup Number 0330.22. After you

69-1730 36Step 11. Configure Installer Setup (Cont)23. Press the Up or Down arrow to select your setting for Installer Setup Number 0500.24. After you

37 69-1730Step 11. Configure Installer Setup (Cont)25. Press the Up or Down arrow to select your setting for Installer Setup Number 0530.26. After you

69-1730 38Step 11. Configure Installer Setup (Cont)27. Press the Up or Down arrow to select your setting for Installer Setup Number 0640.28. After you

39 69-1730Get to Know Your Thermostat ButtonsThermostatM22316UP ARROW BUTTONRAISES TEMPERATURE SETTING ORMAKES SELECTIONS IN OTHER SCREENSDOWN BUTTONL

69-1730 4Step 1. Prepare for Installation (Cont)2. Check that you have everything required for the installation:• Two AA alkaline batteries• No. 2 Phi

69-1730 40Get to Know Your Thermostat Display DisplayM22317SHOWS CURRENTDAY OF WEEKTEMPERATURE SETTINGCURRENT TIMECURRENTSYSTEM SETTINGCURRENT FAN S

41 69-1730Set System SettingSet System SettingPress the System button to select Heat, Off or Cool:Heat—Thermostat controls the heating system.Off—Heat

69-1730 42Set System Setting (Cont)Set Fan Setting 1. Press System & Fan button.2. Press the Fan button to select Auto or On:Auto—Normal setting f

43 69-1730Program Your Heating and Cooling ScheduleYour thermostat can control up to four different schedule periods for each day:Wake—Period when you

69-1730 44Program Your Heating and Cooling Schedule (Cont)2. Press the Edit button.Go BackEdit ViewM22331MonTueWedThuFriSatSun69-1730.fm Page 44 Tue

45 69-1730Program Your Heating and Cooling Schedule (Cont)3. Monday through Friday flashes. Press the Select Day button to select Monday through Frida

69-1730 46Program Your Heating and Cooling Schedule (Cont)4. Press the Next Step button. Once pressed, Wake flashes to show it is selected.5. Press th

47 69-1730Program Your Heating and Cooling Schedule (Cont)12. When complete, press the Done button. “Saved” appears on the display to indicate changes

69-1730 48Set TimeSet Time1. Press Clock & More button.2. Use the Up and Down arrow buttons to set the current time.3. Press the Done button.The c

49 69-1730Set Temperature OverridesHold Temperature Until (Temporary Hold)Hold temperature temporarily until the next scheduled period time.1. Press t

5 69-1730Step 2. Follow Important Instructions1. Do not connect the wires to the new thermostat based on wire color because damage can occur to the he

69-1730 50Set Temperature Overrides (Cont)Permanent HoldPermanent Hold changes the temperature setting until Permanent Hold is cancelled.1. Use the Up

51 69-1730Use Your Filter TimerThe Filter Timer notifies you when to change your furnace filter.Reset Filter Timer1. “Change Filter” appears on the di

69-1730 52Use Your Filter Timer (Cont)View or Reset The Remaining Change Filter Time1. Press the Clock & More button.2. Press the Next button.3. P

53 69-1730Understand Temperature Recovery FeatureYour thermostat comes with a feature called Adaptive Intelligent Recovery™, which eliminates all gues

69-1730 54Replace Batteries1. When the LO Battery indicator is flashing, replace the batteries promptly with two fresh AA alkaline batteries.2. Remove

55 69-1730Replace Batteries (Cont)3. Remove the old batteries and insert two fresh AA alkaline batteries, as marked on the thermostat.M22259BACK OF TH

69-1730 56Replace Batteries (Cont)4. Align the screw blocks with the pins on the back of the thermostat.5. Push the thermostat straight onto the wallp

57 69-1730Review Battery Tips1. Replace the batteries as soon as LO Batt flashes in the display. The LO Battery indicator flashes in the display one m

69-1730 58Built-in Compressor ProtectionThe RTH7500D Thermostat has built-in compressor protection (minimum-off timer) that prevents the compressor fr

59 69-1730Troubleshooting TipsIf . . . Then . . .Display is blank.Check that fresh AA alkaline batteries are installed as marked on the thermostat.Tem

69-1730 6Step 3. Remove Old Thermostat1. Turn off power at the heating and/or cooling system or fuse/circuit breaker panel.2. Remove the cover from th

69-1730 60Cannot set System setting to Cool.Check Installer Setup Number 0170, Heating and/or Cooling System Type; make sure the setting matches the i

61 69-1730Both the heating and cooling systems are running at the same time.Check Installer Setup Number 0170, Heating and/or Cooling System Type, and

69-1730 62Customer AssistanceFor assistance with your Honeywell product, please visit www.honeywell.com/yourhome or call Honeywell Customer Care toll

63 69-1730Limited One-Year Warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under

69-1730 G.H. 06-04 www.honeywell.com/yourhomeAutomation and Control SolutionsHoneywell International Inc. Honeywell Limited-Honeywell Limitée198

7 69-1730Step 4. Follow Special Instructions1. If you have two C and/or C1 wires connected to your old thermostat, do not connect them to your new the

69-1730 8Step 4. Follow Special Instructions (Cont)4. If you have only one C and/or C1 wire connected to your old thermostat, connect this wire to C o

9 69-1730Step 4. Follow Special Instructions (Cont)5. If you find any wires not connected to your old thermostat, do not connect them to your new ther