Honeywell SC1000 Uživatelský manuál Strana 25
- Strana / 174
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
SC Series Instruction Manual page 25
Chassis Models4
Chapter 4
Chassis Models
4.1 Introduction
The SC Series of Signal Conditioners/Indicators are available in several different
chassis models. In general, each chassis model operates in an identical fashion
and can be ordered with any type of Input channels, Output channels, or Virtual
channels.
Input channels and Output channels are printed circuit boards that occupy a phys-
ical slot inside the instrument’s chassis. 12-pin connectors are located on the rear
panel to connect to each Input or Output Channel. Each channel in the instrument
is identified by a number (channel 01, channel 02, etc.).
A Virtual channel exists in software only; it does not occupy a physical slot inside
the instrument’s chassis. There is no rear-panel connector for a Virtual channel.
However, a Virtual channel does require a channel number.
- SC Instrumentation 1
- Contents 3
- Chapter 1 9
- Introduction 9
- 1.2 Related Documents 11
- 1.3 What is the SC Series? 12
- Signature Calibration 14
- Chapter 2 15
- Getting Started Quickly 15
- 2.3 Turn on the Instrument 16
- page 18 008-0608-00 18
- Chapter 3 19
- Operating Modes 19
- 3.3 RUN Mode 20
- 3.3.4 [CHANNEL] button 21
- 3.3.5 [TARE] button 21
- 3.3.6 Indicator Lights 21
- 3.4 ERROR mode 22
- 3.5 SETUP Menu mode 23
- page 24 008-0608-00 24
- Chapter 4 25
- Chassis Models 25
- 4.2 Specifications 26
- 4.3 Models SC1000 and SC2000 27
- 4.3.5 Rack Mounting 28
- 4.3.6 Bench Mounting 28
- 4.3.7 Case Removal 28
- 4.3.8 Internal Arrangement 29
- 4.4 Model SC2001 31
- 4.4.5 Internal Arrangement 32
- 4.4.6 Cleaning 32
- 4.4.7 Vehicle Power Option 32
- 4.4.8 Fuse Replacement 32
- 4.5 Model SC3004 33
- Chapter 5 35
- System Connector 35
- 5.2 System Connector Pinout 36
- 5.3 Function Input Pins 37
- 5.4 Limit Output Pins 38
- System Connector5 39
- page 40 008-0608-00 40
- Chapter 6 41
- System Menu 41
- ARE YOU SURE 44
- ARE YOU SURE? 44
- System Menu6 45
- page 46 008-0608-00 46
- Chapter 7 47
- Serial Communications 47
- 7.3 Communications Protocol 48
- 7.4 Serial Com Menu 49
- page 50 008-0608-00 50
- Chapter 8 51
- Display Menu 51
- page 52 008-0608-00 52
- Chapter 9 53
- 9.2 Limit Operation 54
- 9.3 Limit Menus 55
- page 58 008-0608-00 58
- Chapter 10 59
- Strain-Gage Input Channel 59
- 10.2 Wiring 60
- 10.3 Calibration Procedure 61
- 10.4 Specifications 62
- 10.5 Channel Menu 63
- 10.6.1 Identifying the 76
- 10.6.2 Channel Menu Items 76
- 10.6.3 Output Selection 76
- 10.7 Troubleshooting 77
- Chapter 11 79
- AC/AC-LVDT Input Channel 79
- 11.2 Wiring 80
- 11.3 Calibration Procedure 81
- 11.4 Specifications 82
- 11.5 Channel Menu 83
- HIGH/LOW HOLD 86
- HIGH/LOW CLEAR 86
- TARE OFF 86
- 11.6.1 Overview 93
- 11.6.2 Procedure 93
- 11.7.1 Identifying the 94
- 11.7.2 Channel Menu 94
- 11.7.3 Output Selection 94
- 11.8 Troubleshooting 95
- page 96 008-0608-00 96
- Chapter 12 97
- High-Level Input Channel 97
- 12.2 Wiring 98
- 12.2.2 Bi-polar Voltage 99
- 12.2.3 “3-wire 100
- Voltage” Amplifiers 100
- 12.2.4 “3-wire Voltage” 101
- Amplifiers with Single-wire 101
- Shunt Cal 101
- 12.2.5 “3-wire Current” 102
- Amplifiers 102
- Amplifiers with Buffered 103
- 12.2.6 “2-wire Current” 103
- 12.2.7 “2-wire Current” 104
- Amplifiers with Single 104
- 12.2.8 Low Voltage DC-DC 105
- 12.3.1 Overview 106
- 12.3.2 Setting Jumpers 106
- 12.4 Calibration Procedure 107
- 12.5 Specifications 108
- 12.6 Channel Menu 109
- TRACK / PEAK 110
- TRACK / VALLEY 110
- PEAK / VALLEY 110
- Sub-Menu 111
- Menu Items 112
- Menu Item 113
- Sub-Menu 119
- 12.7.1 Identifying the 121
- Output Type 121
- 12.7.2 Channel Menu Items 121
- 12.7.3 Output Selection 121
- 12.8 Troubleshooting 122
- Chapter 13 123
- Relay Output Channel 123
- 13.2 Wiring 124
- 13.3 Setup Procedure 125
- 13.4 Specifications 126
- 13.5 Channel Menu 127
- page 128 008-0608-00 128
- Chapter 14 129
- DAC Output Channel 129
- 14.2 Wiring 130
- 14.3 Setup Procedure 131
- 14.4 Specifications 132
- 14.5 Channel Menu 133
- 14.6.1 Identifying the 135
- 14.6.2 Channel Menu Items 135
- 14.6.3 Output Selection 135
- 14.7 Troubleshooting 136
- DAC Output Channel14 137
- page 138 008-0608-00 138
- Chapter 15 139
- Split Display Virtual Channel 139
- 15.4 Channel Menu 140
- 15.5 Troubleshooting 140
- page 142 008-0608-00 142
- Chapter 16 143
- Mathematics Virtual Channel 143
- 16.2 Wiring 144
- 16.3 Setup Procedure 145
- 16.4 Channel Menu 146
- 16.5 Troubleshooting 149
- page 150 008-0608-00 150
- Chapter 17 151
- Error Messages 151
- 17.2 Error Message List 152
- UNREACHABLE GOTO 156
- GOTO NOT JUMP 156
- Chapter 18 157
- Setup Menu Reference 157
- Warranty 173
Související produkty a manuály pro Senzory Honeywell SC1000
Senzory Honeywell CTP-20 Uživatelský manuál
(4 stránky)
(4 stránky)
Senzory Honeywell C7189U Uživatelský manuál
(12 stránky)
(12 stránky)
Senzory Honeywell 69-2043EFS Uživatelský manuál
(4 stránky)
(4 stránky)
Senzory Honeywell C7189A Uživatelský manuál
(4 stránky)
(4 stránky)
Senzory Honeywell T7047C Uživatelský manuál
(8 stránky)
(8 stránky)
Senzory Honeywell C7089 Uživatelský manuál
(12 stránky)
(12 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.207 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce