Honeywell HEGS5001 Uživatelský manuál Strana 1

HEGS5000/HEGS5001 Joystick Controller PTZ, MUX, and VCR Control User Guide 900.0800 – June 2006 - Rev 1.01

Rev. 1.01 x 900.0800 19-Jun-06 Notes:

SECTION 1: INTRODUCTON 1.1 PRODUCT DESCRIPTION The HEGS5000 is a controller designed to provide simple operation of the Honeywell KD6/HD6 series domes

Rev. 1.01 2 900.0800 19-Jun-06 Notes:

SECTION 2: INSTALLATION AND EQUIPMENT SETUP 2.1 CONNECTIONS A terminal block is provided for connection between the HEGS5000 controller and peripheral

2.2 INSTALLATION DIAGRAMS InputInputCam 16Cam 1OutputOutputSpotSpotMonitorMainMonitorMainRS-485PSU12 VDC 2ARS-232HEGS5000 System ControllerVCRKX1610CN

2.2 INSTALLATION DIAGRAMS, CONTINUED +12VDCGNDRS-232 (TX)RS-232 (RX)RS-485 (D+)RS-485 (D-)KD6 / KD6ZDome -32KD6 / KD6ZDome - 15511996666991155DB-9 Fe

2.2 INSTALLATION DIAGRAMS, CONTINUED +12VDC+12VDCGNDGNDRS-232 (TX)RS-232 (TX) RS-232 (RX)RS-232 (RX)RS-232 VCR cable connectionsRS-232 MUX cable conn

Rev. 1.01 7 900.0800 19-Jun-06 2.3 EQUIPMENT SETUP 2.3.1 KD6/HD6 Setup The KD6/HD6 Dome must be set to Honeywell Diamond protocol. The address of

Rev. 1.01 8 900.0800 19-Jun-06 Notes:

SECTION 3: MODES OF OPERATION 3.1 MODES OF OPERATION There are two modes of operation when using the HEGS5000 as a standalone controller: 1. HEGS500

Rev. 1.01 ii 900.0800 19-Jun-06 ISSUE DATE REVISIONS 900.0394 1.0 February 2006 Initial Release 900.0800 1.0 June 2006 Correct power supply p

3.2 MODE CONFIGURATION, CONTINUED 3. Press  or  keys to scroll through the available options. • Standalone (control KD6/HD6 PTZs only) • Mux Mod

3.3.1 Default Password Master Default Password is 1994. Operator Default Password is 1111. Master mode has access to all menus. Operator mode allows

3.3.4 Log Out To log off the controller, perform the following steps. 1. Press the Run Menu (Run1. ___3. ___) key until Logout is displayed on the LCD

SECTION 4: SYSTEM SETUP 4.1 SETTING UP THE CONTROLLER The components controlled by the HEGS5000 are defined in the SYSTEM MENU. This menu is availab

4.2 NAVIGATING THE MENUS, CONTINUED • To exit the System Menu, use the joystick to choose menu 8 (Exit), then press Enter () or “Zoom Out” until the

4.3 MENUS, CONTINUED Cameras Menu Name Menu Number Description Cameras 3.0 Used to set the type of camera and the address to which the controller

4.3 MENUS, CONTINUED KDZ SETUP Menu Name Menu Number Description KDZ Setup 4.0 Used to program the address of any KDZ connected to the HEGS5000.

4.3 MENUS, CONTINUED General Menu Name Menu Number Description General 7.0 Used to deactivate the buzzer or set language options. Press Enter (

Rev. 1.01 18 900.0800 19-Jun-06 Notes:

SECTION 5: STANDALONE MODE HEGS5000 5.1 OPERATION When the HEGS5000 Controller is in Standalone Mode, a user can control and program KD6/HD6 PTZ camer

FCC COMPLIANCE STATEMENT INFORMATION TO THE USER: This equipment has been tested and found to comply with the limits for a Class A digital device, pur

5.1.1 Camera (KD6/HD6) Selection To select a camera for control: 1. Enter the camera number (1-256) using the numeric keypad. 2. Press the Camera ()

Table 1. Manual Control, Continued Function Description Freeze Video ( ) Press the Freeze Video ( ) key to freeze or unfreeze the current video sc

5.2 KD6/HD6 DOME MENUS The HEGS5000 controller can be used to program KD6/HD6 PTZ units. 1. Press the Dome Menu (1. ___3. ___) key. The following is

Table 2. DOME MENU (1. ___3. ___) Key – Access/Exit Dome Menus, Continued Menu Description Tour Menu Accesses the KD6/HD6 Tour menu. Use +/- keys

5.2.1 Dome Setup Menu, Continued The on-screen menu is displayed on the monitor where the KD6/HD6 video is viewed. 518584-2980 Rev X 1 Language ...

5.2.2 Program PreShot There are two methods for programming and saving PreShots. The first method quickly saves the current camera scene and assigns

5.2.2 Program PreShot, Continued 6. Press the Enter ( ) key. The following is displayed on the controller’s LCD. Rev. 1.01 26 900.0800 19-Jun-06

5.2.2 Program PreShot, Continued 9. Press the + or – key until the character for the desired action is displayed on the LCD and Press Character Select

5.2.2 Program PreShot, Continued g. Press the +/- key until upper case D is displayed on the controller LCD and then press Character Select (ABC). h.

5.2.4 List Programmed PreShots To view a listing of the programmed PreShots, perform the following steps. This display cannot be edited; it is for v

IMPORTANT SAFEGUARDS 1. READ INSTRUCTIONS – All safety and operating instructions should be read before the unit is operated. 2. RETAIN INSTRUCTIONS

5.2.5 Programming a VectorScan Note: VectorScan Programming is only available to Master users. 1. Press the Dome Menu (1. ___3. ___) key. 2. Press t

5.2.5 Programming a VectorScan, Continued 13. Press Enter ( ) when finished adding PreShots. The following commands are displayed on the bottom of

5.2.7 List VectorScans To view a list of the programmed VectorScans: 1. Press the Dome Menu (1. ___3. ___) key. 2. Press + or – until VectorScan Menu

5.2.8 List VectorScan Contents, Continued 5. When finished viewing the VectorScan contents, press Enter ( . 6. To exit the menu on the LCD contro

5.2.11 Delete a Tour 1. Press the Dome Menu (1. ___3. ___) key. 2. Press + or – until Tour Menu is displayed. 3. Press Enter (). 4. Press + or – unti

5.2.12 Programming Sector IDs, continued 8. Enter the Sector title (up to 24 characters) a. Press the + or – key until the desired character is displ

5.2.12 Programming Sector IDs, continued b. Using the joystick, move the PTZ so the upper right corner of the sector is centered on the monitor, and

5.2.13.1 Programming/Editing/Deleting Privacy Zones, Sony Camera, Continued a. Press the + or – key until the desired character is displayed on the LC

5.2.13.1 Programming/Editing/Deleting Privacy Zones, Sony Camera, Continued 12. Press + or – until the character for the desired action is displayed o

5.2.13.2 Programming/Editing/Deleting Privacy Zones, Hitachi Camera To program privacy zones in a KD6/HD6 with a Sony camera: 1. Press the Dome Menu (

Rev. 1.01 v 900.0800 19-Jun-06 IMPORTANT SAFEGUARDS 14. POWER-CORD PROTECTION – Power supply cords should be routed so that they are not likely t

5.2.13.2 Programming/Editing/Deleting Privacy Zones, Hitachi Camera, Continued c. Press Enter ( ). The following options are displayed on the monit

5.2.13.3 Changing the Privacy Zone Password 1. Press the Dome Menu (1. ___3. ___) key. 2. Press + or – until Sector/Priv Menu is displayed on the LCD.

5.2.14 Nightshot Mode The nightshot feature is only available on KD6/HD6 models with the following cameras: 843216-1011 Sony Color NTSC w/4.1-73.8mm,

SECTION 6: MUX MODE OPERATION HEGS5001 6.1 INTRODUCTION In the MUX mode of operation, the HEGS5001 is capable of controlling multiplexers, VCRs, and K

6.1 INTRODUCTION, CONTINUED The initial display after a user logs on the controller is shown below. The operator has control of camera 1 and Spot Moni

6.2.1 Absolute Mode In absolute mode, the camera number is displayed and selected by a number in the range 001 to 256. Cameras 001 to 016 are from th

6.3 MULTIPLEXER CONTROL The HEGS5001 controller sends basic commands to the multiplexer to simulate pressing the buttons on the front panel of the mul

6.4 VCR CONTROL The HEGS5001 controller sends basic commands to the VCR. Refer to the VCR User Manual for details on the operation of the VCR. To loc

Rev. 1.01 48 900.0800 19-Jun-06 Notes:

SECTION 7: DOWNLOADING NEW FIRMWARE TO THE HEGS5000 7.1 INTRODUCTION New firmware for the HEGS5000 and HEGS5001 controllers can be downloaded through

EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the prese

7.2 DOWNLOADING NEW FIRMWARE TO THE HEGS5000, CONTINUED 5. Press . The controller will clear the memory and, when ready to download, will display t

7.2 DOWNLOADING NEW FIRMWARE TO THE HEGS5000, CONTINUED 8. Click on the red dot on the right of the dialog box to enable the port. Red DotFigure 1

7.2 DOWNLOADING NEW FIRMWARE TO THE HEGS5000, CONTINUED 10. Click on the Transmit Hex File Icon to bring up the Send Hex File window. Note: the h

7.2 DOWNLOADING NEW FIRMWARE TO THE HEGS5000, CONTINUED 12. Select the latest version of the firmware (e.g. 519686-1980_A_HEGS5000-5001.hex) and cli

Rev. 1.01 54 900.0800 19-Jun-06 Notes:

SECTION 8: TROUBLESHOOTING AND MAINTENANCE 8.1 TROUBLESHOOTING If problems occur at the initial installation phase, verify the unit is installed corre

Rev. 1.01 56 900.0800 19-Jun-06 8.3 SERVICING THE CONTROLLER If problems still exist after verifying correct installation and the problem has been

Rev. 1.01 57 900.0800 19-Jun-06 SECTION 9: SPECIFICATIONS Input Voltage 9-12V dc Power 6W Controls Push-button switches with backlit LCD display

Honeywell Video Systems (Head Office) 2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299 www.honeywellvideo.com TEL+1-800-796–2288 Honeywell Video

Rev. 1.01 vii 900.0800 19-Jun-06 TABLE OF CONTENTS SECTION 1: INTRODUCTON ...

Rev. 1.01 viii 900.0800 19-Jun-06 TABLE OF CONTENTS, CONTINUED 5.2.8 List VectorScan Contents .....

LIST OF FIGURES, CONTINUED Figure 6. HEGS5000 Icon Overlay.......................